|
|
Ultrasonic proximity detector DIY kit
with relay control & 3 modes
This listing is for an ultrasonic detector DIY kits with three modes of operation:
High Sensitivity Mode
Low Sensitivity Mode
Toggle Mode
The above video offers a full demonstration of how this device works when assembled. The video below shows you how to assemble it. If you purchase this kit, you HAVE to watch the below video, as there are important assembly notes. The above and below videos act as a full manual for assembly and functionality. No paper instructions will be mailed. Only the parts. This is a fairly straight forward kit to put together. It has an ON/OFF switch, a mode selection button, and a high power relay module that allows for the user to switch on high powered devices when someone or something is being detected by the module. This kit works off of ultrasonic frequency (40kHz). A 40kHz signal is sent off of the transmitter transducer, that signal is bounced back, received and amplified by the receiver transducer/circuitry. That frequency varies depending on how far away the object is from the module. Again, please watch the above video for a full demonstration and the below video for assembly instructions. The relay pin-out is talked about below. The power supply pinout is talked about in the video. This device requires 7-10v to operate. If you want an AC adapter shipped with this kit, let me know. I can send a 9v 1A wall adapter for an additional $7. By default, this kit does not come with one. If you have any questions, please do not hesitate to ask!
These pins are labelled:
NC - Normally Connected to the Common Pin
CO - Common Pin (Connected to the NC pin when the relay is off / Connected to the NO pin when the relay has been activated)
NO - Normally Open. This pin is not connected to the Common Pin until the relay is activated.
Specifications:
Input Supply Voltage: 7-10VDC
Standby Current: <20mA
Relay-ON Current: Roughly 55mA
Length: 70mm
Width: 61mm (With Transducer attachment soldered into place)
Height: 22.5mm
Disclaimer:
This prop module was created specifically to enhance your tactical gaming experience. Engineeringshock Electronics, paintballprops.com, and any affiliates of Engineeringshock Electronics will not be held accountable for losses or consequences caused by the misuse of this product, or any of our products. Furthermore, we will not offer servicing on products that have been modified in any way. By purchasing this product, you are agreeing to the above statement. Engineeringshock Electronics, paintballprops.com, and any affiliates of Engineeringshock Electronics prohibit the re-sale of this product, or any of our products.
Assembly Video:
High Sensitivity Mode
Low Sensitivity Mode
Toggle Mode
The above video offers a full demonstration of how this device works when assembled. The video below shows you how to assemble it. If you purchase this kit, you HAVE to watch the below video, as there are important assembly notes. The above and below videos act as a full manual for assembly and functionality. No paper instructions will be mailed. Only the parts. This is a fairly straight forward kit to put together. It has an ON/OFF switch, a mode selection button, and a high power relay module that allows for the user to switch on high powered devices when someone or something is being detected by the module. This kit works off of ultrasonic frequency (40kHz). A 40kHz signal is sent off of the transmitter transducer, that signal is bounced back, received and amplified by the receiver transducer/circuitry. That frequency varies depending on how far away the object is from the module. Again, please watch the above video for a full demonstration and the below video for assembly instructions. The relay pin-out is talked about below. The power supply pinout is talked about in the video. This device requires 7-10v to operate. If you want an AC adapter shipped with this kit, let me know. I can send a 9v 1A wall adapter for an additional $7. By default, this kit does not come with one. If you have any questions, please do not hesitate to ask!
These pins are labelled:
NC - Normally Connected to the Common Pin
CO - Common Pin (Connected to the NC pin when the relay is off / Connected to the NO pin when the relay has been activated)
NO - Normally Open. This pin is not connected to the Common Pin until the relay is activated.
Specifications:
Input Supply Voltage: 7-10VDC
Standby Current: <20mA
Relay-ON Current: Roughly 55mA
Length: 70mm
Width: 61mm (With Transducer attachment soldered into place)
Height: 22.5mm
Disclaimer:
This prop module was created specifically to enhance your tactical gaming experience. Engineeringshock Electronics, paintballprops.com, and any affiliates of Engineeringshock Electronics will not be held accountable for losses or consequences caused by the misuse of this product, or any of our products. Furthermore, we will not offer servicing on products that have been modified in any way. By purchasing this product, you are agreeing to the above statement. Engineeringshock Electronics, paintballprops.com, and any affiliates of Engineeringshock Electronics prohibit the re-sale of this product, or any of our products.
Assembly Video: